• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they are not susceptible to get rusty or decay.

It is crucial to wash and oil UPVC doors and windows regularly. This will help avoid unnecessary door repair costs as well as increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large amount of damage to your home, which can make it very hazardous and possibly fatal. It is essential to ensure that your windows are in good condition.

For single pane windows it is fairly easy to replace windows, and the new one is usually able to fit into the old frame very easily. If you have repairing double glazing-paned windows that are held together by internal beading, it will be harder to remove and replace the old panes. In this situation you'll need source some plastic spacers that assist the new pane to fit perfectly into the window frame.

If you plan to attempt to remove the window panes by yourself, it is essential to wear appropriate safety gear such as gloves that are thick and eye protection. It is also a good idea to lay down a drop cloth prior to when you start working on the glass, so that any fragments of glass fall on the fabric instead of landing on the floor where they could be trampled upon and cause further damage.

After the glass has been removed, it's a good idea to seal the gap with packaging tape or duct tape to block water and drafts from getting into the home until a professional is able to come out and fix the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the distance between the door repairing and the window is large, you might need to consider a security screen that also includes a window. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. As time passes, they may be affected by a variety of issues, including sliding. A window that is sagging can cause problems with light, draughts and even security. It is crucial to act immediately if you notice your uPVC windows are sagging.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll need to open the window to access the frame. You can then unscrew both the hinges at the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they remain in place.

If you aren't able to move the hinges, you may require replacing the seal. Over time, rubber seals lose their elasticity and become dry which causes them to loosen. It is essential to replace your seal as soon as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles may also become loose. This is often caused by screws that have loosened over time, but it could be caused by the handle mechanism getting worn out. Fortunately, it's easy to fix the loose uPVC window handle yourself. First, you'll need to close the window and do an initial fitting. The joints at the corners of the sash should align with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle and return the mechanism to its original position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls every time it rains it is important that you take action. Windows that leak water do not only lead to the destruction of your home's structure but also hinder your efforts to regulate the temperature in your home. The most common reason for leaking uPVC windows is that the sealant around the frame has been damaged or not present.

This is a relatively easy fix and should be undertaken by any competent DIYer. Based on the severity of the issue the old caulking may need to be removed before a new layer is applied. It is important to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk and then make the area more difficult to clean and could reduce your energy efficiency.

It is important to check that the drainage holes are clear of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious situations, you might have to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread across the house.

If the leakage occurs between the double-glazed glass, it is more likely the problem is with the seal than the frame. Again this can easily be repaired by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open in a breeze It could be the hinges that are at the fault. They can be repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical component hinges will be damaged over time. It is essentially a simple procedure, but it is easier when you have a person to assist in holding the frame up.

Make sure that the uPVC hinges are open and closed in the correct direction. Look for the arrows on each hinge to determine which way the window should be opened.

The issue could be caused either due to opening the window in the wrong way or a faulty installation in the factory. Sending us a photo via our website is often enough to solve the issue. We are more than happy to give suggestions.

It is also essential to ensure that the hinges are lubricated regularly. Applying a light engineering lubricant on the hinges is a great way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the chance of windows sticking and help prevent corrosion. This is recommended to be done at least once a year. WD40 or other solvent-based oils are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different things. The hinges can also be unbalanced due to wear, which can cause an opening where the sash meets frame. If they are beyond repair, it may be necessary to have them realigned. Secondly the interlock, this is located on the hinge of the window, may also be misaligned, and again it is feasible to give them a thorough clean, however in certain cases, it may be necessary to get them replaced.

The second most frequent reason for draughts is window seals. They are susceptible to being worn out or damaged over time, and let air escape through the gaps. Installing high-quality weatherstripping can help keep draughts at bay. Replace the upvc windows with low-emissivity glass. This will help control indoor temperatures, and reduce the possibility of draughts.

The last way to reduce the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler which can be placed over your window sill. They can keep your home warm by blocking out cold air.

With a little regular maintenance and repairs, your upvc windows will provide an excellent level of security and insulation for your home. It is essential to remember that all windows eventually become worn out, and it is more cost-effective to replace them instead of fixing them. So, if you are experiencing issues with your Upvc windows, it's best to seek professional assistance as soon as possible.