• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge - take a look at the site here, a Loose Door Hinge

Fixing a door hinge that is loose is a simple task for most homeowners. If the screws' holes have been smashed and will not hold screws, you may require wood glue and dowels in order to reinstall the hinge.

Remove any surface corrosion. This will help the dowels stay in place and give them a solid base to hold onto.

Take the Hinges off

A lot of door hinges are able to be removed, making it easier to move the door from one side to the next or to take the entire upvc door hinge types off of the frame, if needed. Anyone with a bit of patience can remove the hinges but you need to know what to do.

If the hinges are painted, you'll need to take off the paint prior to attempting to remove the pins. You could scratch your door if do not remove the paint. To break the seal put the hinges into a stainless steel dish and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to get rid of the pins.

After the pins have been loosened, remove the hinges and frame from the door. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this project. This type of screwdriver was designed to pick up screws made of steel and will make the project go much faster.

It is a good practice to spray lubricant on the hinges prior to attempting to remove them. A simple lubricant will help the process move along quickly and make it easier to remove the pins and screws. You can purchase this kind of lubricant at most hardware and home improvement stores.

It is important to keep in mind that the number of hinges you'll require will differ based on the type of replacement upvc door hinges and its settings. Doors with a heavier core and solid-core will need more hinges, while hollow-core doors that weigh less might require just two or three.

Understanding the different kinds of hinges will help you determine which one is suitable for your situation. Exterior hinges are designed to withstand the weight of a door, while interior hinges need to be able support lighter loads.

Reattaching the Hinges

Sometimes, a hinge on a door will get looser and eventually begin to hang out of alignment or sag. This can be a problem, but it's usually easy to repair. A simple tightening can solve the issue. If the screw holes have been ripped out, it can be a challenge to complete. There is a trick to make these holes back to their original size that utilizes a wood dowel.

Begin by drilling the hole using a drill bit close to the size of the new screw (normally 3/8"). Then use wood glue and a dowel made of wood to fill in the hole. To ensure a tight fit, the dowel should be cut at the same length as the screw. Then, reinstall the screw and tighten it until the desired tightness. If the door continues to bind up, you can insert another dowel to the gap. Repeat the process. Be sure to close the door slowly so that you can check the perimeter clearances after each adjustment.

You could also use a wood plug instead of the dowel. It's also possible however it will take a bit longer to install. Simply whittle a piece of wood to the proper size to ensure a secure fit, and then insert it into the hole. If you don't have a woodworking tool you could also make use of toothpicks or wooden matches as well.

Use a countersink to make the hole smaller than the head of screw after you have put it back in place. This will prevent the screw from rubbing against the edges of the doors when they are closed and opened. This will make it much easier to tighten the screws after replacing hinges.

Once you have reinstalled the hinge, make sure to grease it with a dry lubricant in order to help keep it from getting stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a thin coat and wait for around 15 minutes to fully get into the hinge barrel.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you can do a few simple repairs. The first step is to check that the screws securing the hinge plate to the door frame are tight. If they're loose, tighten the screws with a power drill or screwdriver. Be cautious not to tighten the screws so tight that they create gaps at the trim joints, or worse remove the threads.

If the problem is the hinge plates are separating they can be reattached to the plates by applying wood glue on the back of them and then inserting toothpicks or wooden dowels into the holes. The toothpicks or dowels will give a solid foundation for the screws and prevent the plates from shifting when you drive them into the holes. Allow the glue time to dry before reattaching the hinge.

The screws may also be stripped or missing. This issue can be resolved by replacing the screws. Be sure to use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the upv door hinges once you've reattached the hinge and measure the gap between the frame and the door. It should be approximately the thickness of a nickel all the way around or less if there's a gap caused by a door that hung improperly. If the hinges were installed correctly, this should not be a problem.

If you discover that the hinges are still loose, try putting a thicker hinge shim between the hinge plate and the mounting surface, to create an extra inch of space. You can also try removing the hinge pin from the problem hinge and pounding it with a hammer in order to make it more secure or using an entirely new hinge pin. You can also lubricate your hinges with mineral oil or jojoba to reduce friction and help keep them in their place. Regularly lubricating your hinges will help keep them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges, if they're not maintained and cleaned regularly. The hinge will become stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection will preserve the integrity and functionality of hinges on a door.

Check the hinges for corrosion. If the rust is so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you can save the hinges, you should first clean off any loose rust with steel wool and a wire brush. Then, apply an industrial rust remover or a homemade solution such as lemon juice on the hinge. Let the rust remover remain on the hinge for several minutes to penetrate and dissolve any remaining corrosion.

The tightening of screws can restore hinge function If you don't wish to spend money or time to replace hinges. If you've stripped the screw holes however, it might be necessary to add an wooden dowel or shim to the hinge. Wooden dowels are round pieces of wood that are in the form of rods that are available in different sizes and lengths. You can find them at home improvement stores or woodworking supply shops, or on the internet.

A shim could be made of a piece of metal or plastic, depending on the kind of hinge you've got. To make a dowel cut a piece of wood dowel or another sturdy material to the size you want. You can then dip the dowel in a glue for carpenters and then insert it into the cut hole and let the glue hold the dowel in the desired position.

Before cleaning the hinges, lay down a cloth or towel to protect your flooring from spills. After the area is secured, proceed to clean the hinges using a soft sponge or cloth that has been soaked in mild cleaner or vinegar to eliminate the build-up of dirt, grime and tarnish. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in crevices or tight areas.